How To Make Ebb Tides On The Roof With Your Own Hands, A New And Rustic Way

2023 Author: Philip Bishop | [email protected]. Last modified: 2023-08-25 07:54

• What kind of gutter do you need?
• Preparations for installation
• What tools are needed?
• Work sequence
• How to fix the gutter
• What other materials can I use?

Roof drips are a necessary element that can protect it from water and extend the life of the structure. Installation of these simple devices does not take much time, and you can do it yourself; for this you only need to follow the instructions and stock up on everything you need.

The main task of this structural element is to remove moisture in the right direction. Thanks to the ebb, the blind area of the house will last longer, and the foundation and walls will not gain excess moisture. In winter, icicles will not form, which, if dropped from a height, can cause serious injury to people below. In the presence of ebb tides, the task takes on a completed form. They can serve as an element of decoration or, on the contrary, be invisible.

What kind of gutter do you need?

Before making ebb tides on the roof with your own hands, you need to purchase all the necessary materials. It is better to purchase the complete set immediately. It will be necessary to carry out calculations: you need to find out the area of the slope, relative to this, the diameter of the trough is also chosen. The formula is simple: 1 sq. m roof requires 1.5 sq. see gutter. For example, if the roof area is 100 meters, you will need a 15 cm wide gutter.

Preparations for installation

The installation of a roof ebb should begin with the preparation of the necessary tools and structural elements. It will be most convenient to mount plastic parts. You will need the following items to purchase:

• Chute: the length should be slightly less than the size of the side on which it is installed. You can buy a little more material just in case.
• Funnels.
• Connecting inserts: they will be required as many as planned joints in the gutter. This is influenced by the length of the purchased gutters and the roof line. The insert also helps to avoid deformation of the gutter. It can be used as a stiffener, so if you do not need to connect the elements, it is still worth buying several inserts.
• If you do not plan to make closed ebb tides for your home , you will need to buy plugs.
• Ebb brackets: one is required for each meter of structure.
• Clamps for fixing the drain on the wall.
• A drain pipe equal to the height of the house.

Roof eaves, if not straight, must have corner fittings.

What tools are needed?

Installing roof sills will require the following tools on hand:

• Screwdriver.
• File.
• Metal file.
• Pencils and building level.
• Rope.

The place where the water will drain from the roof is prepared in advance. It is chosen so that moisture does not create inconvenience: for example, drains should not flood the sidewalk or plants planted in the yard. Water should not have access to the foundation in order to wash it away: you can get rid of this with the help of storm sewers. If not, pierce the water drainage groove. You can install a barrel, but over time, the water will need to be drained somewhere.

Work sequence

Do-it-yourself installation of ebb tides on the roof begins with marking. To do this, you need to determine where the ebb will be attached. The funnel is installed first. Focusing on it, you can draw a centerline, which will become a guide for the rest of the work. Holders are placed on both sides of the funnel, 15 cm away from it.

You need to install the funnel in such a way that water does not fall into its center, but onto the edge. This trick comes in handy for heavy rainfall. If water gets into the center, it will overflow over the edge of the structure. The gutter must have a certain slope. It is difficult for a beginner to achieve this at first. For one meter of the structure, the slope should be about 3 mm: it is necessary so that liquid does not accumulate in the gutter.

Before installing the ebb on the roof, you need to mark the slope of the gutter. This will require a long board and a building level. Use one of the edges of the holder that will already be installed. Draw a zero line: it should go to where the next funnel holder will be attached.

We'll have to calculate the difference that should arise between the fasteners. It needs to be multiplied by three. Install the next roof sill attachment, taking this offset into account.

How to fix the gutter

After the fasteners are installed, the do-it-yourself installation of the roof eaves goes into the stage of attaching the water gutters. First, you need to adjust them in length. The pieces of the part must be put in the fasteners, not forgetting to leave space for the connecting inserts. Their size can be measured in advance, usually about 10 centimeters are left.

If the chute is too long, it can be shortened; you will need to use a hacksaw. The cutting site is cleaned with a file. In order to make your work easier, put a plug on the end of the pipe immediately while standing on the ground. It is quite difficult to do this on weight. Individual parts of the gutter can be connected using inserts. For convenience, they have special marks.

After assembling the gutter, it must be fixed on the holders, then check if the required slope is present. To do this, it is not necessary to take measurements, it is enough to pour a little water into the gutter and see if it flows out or remains in place. If no liquid flows out, the slope must be increased.

After it was possible to correctly install the ebb on the roof, you can proceed to the installation of the downpipe. Work starts from the funnel. If the length allows, the pipe can be immediately connected to it, otherwise, you will have to install an elbow: it will help to avoid splashes and force the water to drain into the pipe.

Usually the pipes are 2 meters long. We'll have to calculate how much material and connecting elements are required. Do this beforehand.

What other materials can I use?

Do-it-yourself ebb tides do not have to be made of plastic or metal elements made specifically for this. A good owner can save money and make the necessary items on their own. To do this, you will need to find suitable galvanized strips or any pipe of a suitable diameter that can be cut lengthwise. It is most convenient to work with a plastic pipe, you can use a metal one. Asbestos pipes are not suitable: they crumble when trying to cut and have a large mass.

The options for attaching roof eaves can also vary. Their independent production is quite available. The main thing is to comply with the following rule: the roof should fall approximately in the middle of the gutter or closer to its inner part. The slope must be at least 3 mm per meter of structure.

Conclusion : the installation of roof ebbs is a simple procedure that an amateur can handle, having thoroughly studied the theory and prepared the necessary tools.

Video: