2023 Author: Philip Bishop | [email protected]. Last modified: 2023-05-24 22:24
- Where to start?
- Basic rules for laying an apron in the kitchen with tiles
- The procedure for laying tiles on an apron
- Tips for beginners:
It is customary to call an apron the vertical part of the wall that connects the wall cabinets and the countertop together.
The apron should be made of a material that is easy to clean, is not exposed to chemicals, and is resistant to temperature extremes.
Most often, the apron is laid out from ceramic tiles. A wide variety of colors, patterns, ornaments, sizes allows you to create aprons from ceramic tiles not only to protect the wall surface, but also to improve the design of the room. To find out how to properly lay out an apron in the kitchen with tiles, just read our article.
Where to start?
The work begins with calculating the required amount of material, determining the method of laying the tiles, preparing the accompanying material and tools.
Let's start with the tiling method.
Most often, the standard installation method is used, in which the tiles are placed in horizontal rows. It is also called basic. There is also a diagonal tiling method.
At cost, the diagonal method is more expensive.
Do not forget that when working with ceramic tiles, marriage is inevitable due to its fragility.
Having calculated the total area of the apron, divide by the area of one tile and, adding another 10% to the resulting amount, you will get the required number of tiles.
It remains to clarify how to lay out an apron in the kitchen with your own hands and get to work.
Basic rules for laying an apron in the kitchen with tiles
Before you start laying the apron, here are some helpful tips:
- It is recommended to make the apron height greater than the distance from the table to the lower edge of the wall cabinets.
- The bottom of the apron should be 2 cm below the edge of the table top.
- The apron is made either over the entire area of the vertical wall or selectively: over the hob and sink.
- As a rule, the distance from the countertop to the upper drawers is from 55 cm to 60 cm.
The procedure for laying tiles on an apron
An apron with their own hands can be laid out by anyone who knows how to hold a trowel in their hands.
A few words about tools.
You will need a trowel, three types of spatulas: notched, regular and rubber for grouting. It is best to control flatness with a rail and a building level. Tile cutting is preferable with a tile cutter.
Do not forget about a pencil and a ruler, without them you cannot mark up.
All these accessories will help you lay out an apron in the kitchen with your own hands.
In order to find out how to lay out an apron from tiles in the kitchen, you must correctly complete the preparatory stage.
Having marked out the area for laying the tiles, proceed to surface preparation:
- be sure to remove the old coating;
- old tiles and plaster are removed to the brickwork;
- the rail checks the flatness of the surface;
- level the surface with cement mortar or plaster mixtures;
- priming the wall.
To remove old tiles, spread a protective film on the floor and cover furniture and kitchen utensils.
Tiles are removed with a perforator or manually using a chisel and hammer.
If the plaster only crumbles, then it must be removed to the brickwork.
After cleaning, the surface of the wall is treated with a primer.
And how to lay out an apron from a tile in the kitchen, if you have a minimum of knowledge?
To properly lay out the apron in the kitchen, start with the layout
You will need a cord to bounce off the lower horizontal level.
A metal profile for plasterboard is applied according to the markings and attached to the wall with dowel-nails. The installation of the profile guarantees you against collapse of the ceramic tiles being laid and will allow you to lay the first row evenly.
A vertical line is bounced in the center with a plumb line and a cord.
The tiles are laid with glue or cement mortar. Find out how much tile glue you need with a calculator.
To lay out an apron from a tile in the kitchen, you first need to prepare glue. The glue is diluted according to the attached instructions using a drill.
It is better if you use a special drill attachment.
And here are tips on how to lay tiles on an apron.
To lay out the apron in the kitchen, start from the bottom row, from the middle of the surface to the edges.
Before installation, lay the tiles on the floor using the spacer crosses. This will allow you to see the final picture.
It is best to lay a tile backsplash in rows. The next row is laid after installing the entire previous row.
It is allowed to lay tiles on the apron not only in a solid, but also in a square-nesting way.
Glue is evenly applied to the tile, spread over the tile with a notched trowel, and the tile is laid on the apron. It is best to use a trowel with notches up to 6 mm.
The tile should be attached to the wall, slightly pressed down, if necessary, knocked out with a rubber mallet.
Check each row for horizontal and verticality using a building level, and the resulting plane with a rail.
It remains to clarify how to lay the tiles in the kitchen apron.
When laying tiles on an apron, pay attention to the flatness of the resulting surface. If the tile is sunk or its corners protrude, the tile is removed, glue is added or excess is removed. The tile is reapplied to the surface.
Do not hurry. Each subsequent tile is laid in the same way.
Place crosses at the joints of the tiles.
When you have laid all the whole tiles on the apron, you can start gluing the pieces.
Measure each piece carefully, bring the dimensions to the blanks and cut with a tile cutter.
Try to cut the workpieces as accurately as possible.
If necessary, holes in ceramic tiles are drilled with diamond drills.
The control of laying the tiles on the apron is carried out the next day. You can learn about the methods of tiling by watching the video.
If voids are found under the tiles, the tiles are pulled out, cleaned of glue and glued again.
At the last moment, the crosses are removed and the metal profile is removed. You installed it at the bottom of the apron structure.
In the next step, after the ceramic tile apron is completely dry, start cleaning the surface. Washing with a sponge is best done with detergents diluted in warm water.
Then you need to take a wooden or plastic stick and thoroughly clean the seams, then wipe the surface with a rag.
Laying tiles on an apron ends with grouting. Calculator will help to find out how much grout for tiles will be needed. The grout is rubbed into the seams with a rubber trowel. After half an hour, the remains of grout are removed, the surface of the tile is carefully wiped with a sponge or cloth. Using an electric wire, the seams are aligned.
Now you completely understand how to lay out an apron in the kitchen with your own hands.
But a few helpful tips won't hurt. A way to wipe hardened adhesive or grout off a tile.
Tips for beginners:
- you can lay out an apron in the kitchen with your own hands not only from a traditional tile;
- special sets of tiles with decorative modules are produced;
- do not overdo it with decor;
- it is recommended to combine matte countertops with similar apron surfaces;
- for the visual expansion of the room, it is advisable to use light-colored tiles.
It all depends on your preferences and taste. Further, a video on laying ceramic tiles on an apron will help you understand the intricacies of work.