How To Dismantle An Old One And Install A New Toilet With Your Own Hands Video

2023 Author: Philip Bishop | [email protected]. Last modified: 2023-08-25 07:54

• Required items
• Training
• Dismantling
• Toilet installation

Installing a toilet with your own hands is a rather difficult task and will require certain skills and tools. However, if you do it yourself, then, firstly, you can save on a specialist, and secondly, gain invaluable experience - after all, new skills are always useful.

Toilets, due to their variety, differ in the way they are installed. The most common type is outdoor.

Required items

Before you install the toilet with your own hands, you need to make sure that there are items that will be needed in this matter:

• Perforator;
• Boer;
• Adjustable wrenches and wrenches;
• A hammer;
• Screwdrivers;
• Sealant;
• Transfer collar for connection to a cast iron socket;
• A container where water will be drained from a dismantled plumbing device, as well as rags to wipe.

Video:

Training

Before you change the toilet with your own hands, you will need to carry out preparatory measures. First, you need to determine in what way the new device will be connected to the sewer. There are three cuff options:

Corrugated - this connection method is the most cost-effective. However, with this method, installation cannot be carried out close to the sewer pipe

Before connecting the toilet with a corrugated sleeve, you should make sure that the room has the necessary space and will comfortably fit the equipment.

• Direct - a universal connection method, it allows you to do it reliably. If there is any hesitation in choosing the method of connecting to the sewer, then this option is the best.
• Eccentric - a method of connecting to the sewage system, it is convenient if the centers of the drain and the bell are displaced.

To properly install the toilet with your own hands, it is recommended to dismantle the old eyeliner and put a new one. Its length should be equal to the distance from the water supply pipe connection to the toilet bowl connection, plus 15-20 cm.

Dismantling

Before you change the toilet, you will need to dismantle the old one. For this you will need:

• Disconnect the water supply;
• Disable eyeliner;
• Drain the contents from the barrel;
• Remove the barrel. If the old toilet is not planned to be used anywhere, then this can be done with a hammer, otherwise you will have to act carefully;
• Remove the fixing tools with which the bowl was installed, remove it by pouring out the remaining water.

If you decide to use brute force and use a hammer or puncher to dismantle the old toilet bowl, then you should be careful not to allow various debris to enter the drain, which will cause a blockage.

If there is some kind of support made of wood or other material under the old bowl, then it must be removed. The void that remains after this operation must be filled with cement and leveled with a spatula.

www.youtube.com/watch?feature=player_embedded&v=Y1XRh22HZKE

Toilet installation

Before you put the toilet on your own, you need to clean the socket from rust and dirt. Then you need to cover with sanitary sealant and connect the cuff

When the toilet is dismantled, odors come out of the drain. So that they do not distract from work, the sewer hole must be closed with something, for example, plugged with rags.

Do-it-yourself installation of the toilet continues with markings for dowels. For this, the bowl is placed in the place where it is to be installed, and the holes are marked. Drill holes according to this marking and insert dowels into the holes

On some models, holes are drilled at an angle. In this case, to install the toilet in the holes, you must drill at the same angle.

When the dowels are inserted, the bowl is put into place and connected with a collar from the sewer socket. Then the screws are tightened, onto which the plastic washers are put on

It is not correct to tighten the screws immediately. First you need to lightly make money, and assess whether the installation was done smoothly. If not, then align by substituting plastic pads under it. Only then can you tighten.

To install the toilet, you need to assemble the barrel yourself if it is delivered disassembled. Here, everything should be done according to the instructions supplied by the manufacturer

All moving parts must not be in contact with each other or with the walls of the drain tank.

The next step is to install the drain tank on the bowl. Fastening is usually done with bolts, which should be tightened evenly. When the installation is completed, a lid is put on the tank and a drain button or lever is installed

It is recommended to put a spacer between the bowl and the barrel. To prevent the gasket from moving, it is better to glue it with a sealant.

The final moment of self-assembly of the toilet is the connection of the piping

When the eyeliner is connected, do not rush to turn on the water. First you need to visually check for damage to all structural components. And only if you are confident that everything looks normal, you can open the water, fill the tank and try to rinse it off. If there are leaks, then they must be eliminated.